Paper DIY Pinhole Camera Kit Online Instruction

Step 1: Take out part 1-a carefully	Step 2: You will find out one side is smoother than the other of part 2-d. Put on some glue on smooth side.	Step 3: The side with printing of part 1-a should face down. Carefully matching the hole of part 2-d and part 1-a. part 2-d should able to fit into the marks already stamped on part 1-a. If unable, may require to rotate part 2-d. Stick part 2-d on part 1-a.
Step 4: Fold along the marks stamped on part 1-a	Step 5: Fold and put some glue on the two side of part 1-a	Step 6: Fold and hold for 15 sec to make sure the glue has dried.
Step 7: Now part 1-a should look like this.	Step 8: Repeat Step 5 and Step 6 on the othe side. part 1-a should look like a box shape after Step 8	Step 9: Fold along the marks stamped on part 1-a to inside of the box
Step 10: Now all four side should fold inside the box of part 1-a	Step 11: Take part-2a and put some glue on the smooth side of the second section of part 2-a	Step 12: Fold the second section of part 2-a and hold for 15 sec.
Step 13: Put some glue on the smooth side of the forth section of part 2-a	Step 14: Fold the forth section of part 2-a and hold for 15 sec	Step 15: Fold the first and third section of part 2-a along the marks
Step 16: Now you can fold part 2-a into a box shape	Step 17: Put some glue on the top and bottom of part 2-a show on the picture of Step 18 which connect to part 1-a	Step 18: Make sure the thicker side of part 2-a is on the bottom. Put part 2-a into part 1-a and hold for 15 sec.
Step 19: Put the washer on one side of the spoll.	Step 20: Put the washer and spoll make by Step 19 into the left hand side of the main component finished at Step 18	Step 21: Install the other washer in between the spoll and the main component
Step 22: Install the the aluminium winder and screw into the spoll	Step 23: Now the finishing should look like this. The winder should be loose tight. So the whole spoll can spin freely while winding.	Step 24: Use the pin to make a hole on the centre of the copperplate
Step 25: Use the sandpaper to polish the rough part near the hole carefully	Step 26: Put some glue of the edge of the copperplate	Step 27: Stick the copperplate on the main component
Step 28: The pinhole should be at the center of the hole of main component	Step 29: Put some glue of smooth side of part 2-b and hold for 15 sec. There are one spare part of part 2-b, do the same	Step 30: The othe aluminium winder of the left hand side of the main component
Step 31: Put in the part 2-b to hold the aluminium winder from falling out	Step 32: Take out part 3-a and part 3-b	Step 33: Fold along the marks of part 3-a and part 3-b. The printing of part 3-a and part 3-b should be on the outside. Put some glue of the edges and hold for 15sec
Step 34: Now the finished part 3-a look like this	Step 35: Now the finished part 3-b look like this	Step 36: part 3-a and part 3-b is the cover of the pinhole camera
Step 37: Take out part 2-e and fold. The priniting of part 2-e should be on the outside	Step 38: Put part 2-e at the back of the main component	Step 39: Take out part 2-c and put on the front of the camera. Make sure upside of part 2-c matches the upside of the main component.
Step 40: Install part 3-a and part 3-b from left and right	Step 41: The back side of the camera now look like this	Step 42: To close the shutter, you can move part 2-c to the close side.
Step 43: To open the shutter, you can move part 2-c to the open side. The pinhole camera has completed!! Enjoy!!	There are information of exposure reference time at the back of the camera.

This online instruction is created by www.holga-magic.com Copyright c 2009 HOLGA MAGIC Online Shop.